Media Library / Images

Camlock Cam Locking Coupling AMK 50 Ms (brass)

Oasis BV708, 1" ball valves, isolation valves, CNG spheres (tanks)

ROTEX Rubber Expansion Joints

Biomass powerplant

Production MannTek, Sweden

IBC unloading

Coupling of Chemopal chemical hose assembly with AMKC 50 SS (Camlock female with Spannloc attachment) to AMKI male coupling. Use of IBC-adapter RS 60 x 2 SS.

Elaflon Plus FEP

hose assemblies, lacquer filling

ROTEX 80.16

Rubber Expansion Joint suitable for permanent use with hot heating water, cooling water and hot air. Approved according to DIN up to 100° C by 10 bar and up to 110° C by 6 bar. Temperature range (depending on medium) - 40° C up to + 130° C, temporarily up to + 150° C. Electrically dissipative

Urea solution filling, truck:

'ZVA HV for AdBlue^®' nozzle, 'Slimline 16 for AdBlue^®' hose

Boat refuelling, ZVA Slimline 2 GR

Vehicle refuelling with LPG (L.P. Gas, Autogas)

GasGuard GG20 ACME nozzle

GasGuard GG11R

The GasGuard GG11 Back-Check Valve (GG11R: with additional release screw) should be standard equipment for any LPGas road tanker operator. It is used in conjunction with LPGas bulk refueling nozzles to contain leaks at storage tank fill points. If the fill point proves to be leaking when removing the nozzle it can be left on the tank until corrective action is taken. The driver can move to the next fill point without delay.

Bunkering ship: FHD hose assemblies

M 21-1" NR cr

Female ferrule hose coupling EN 14424, factory assembled, non-reattacheable. Slimline 21 hose, yellow.

DDC-K ADR:

DDC Dust Caps with Pressure Relief Valve to ADR Requirements. These pressurized dust caps PN 10 of aluminium for DDC male adapters on road tankers are much lighter than the PN 25 versions of stainless steel.

Alternative fuels: B 20 (Diesel with up to 20% Biodiesel), E 85 (Gasoline with up to 85% Ethanol)

ZVA Slimline 2, ZVA Slimline 2 GR

LPG Autogas Adapter (filler inlet) EURO

Push-In-Coupling EN 13670

TSVC 100 hose connectors

Fittings to conect two hose assemblies - available in many sizes, with Spannloc or Spannfix clamps

Slimline 16 green

Quality petrol pump hose for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B 30 (BIO Type up to B 100). Meets weights and measures regulations, see overleaf. Cold flexible down to - 30° C / - 22° F (LT-type down to - 40° C / - 40° F). Corresponds to EN 1360.

Cargo loading of a tanker with petroleum based products; FHD hose assembly with new longitudinal stripe to avoid torsion

Picture courtesy of Macoil International, Gibraltar

Truck refuelling with LPG (L.P. Gas, Autogas)

ZVG 2 ACME nozzle, LPG 16 hose

ZVA Slimline 2 GR

blue scuffguard, blue produc sleeve, guard no. 4

NR ferrule hose fittings, non reattacheable

ELAFLEX Hamburg, stock

ERV-BR 300

for abrasive Media

MannTek DGC DryGasCouplings for L.P. Gas

DGC-M 50 F, DGC-M 80-3", DGC-M 50-2", LPG hose

KSS-SD of stainless steel

for saturated steam hoses. These hose assemblies are subject to high wear. The main stress area for hose assemblies is also at the joint end is protected.

Stainless steel couplings with PFA coating, type "...SSE"

Surface in contact with the medium additionally coated with Teflon® PFA. This type is used if stainless steel does not have a sufficient chemical resistance (i.e. for hydrochloric acid and iron-III-chloride) and polypropylene is not possible because of insufficient stability. Available in all standard sizes.

Terminal / gantry: 'Polypal Oil 100' and 'TW 100' hose assemblies for bottom loading of road tankers

Maintenance at the petrol station

ERV-G 100.16 SS TA

Yellow Band Rubber Expansion Joint PTFE lining