Media Library / Images

UTS 200 hose assembly in chemical plant

Italy

Grafik ARK 19

Safety Break for LPG (Autogas) dispensers. Hose Break. Reassembly after separation without tools.

Elaflex Cam and Groove Couplings ('Camlock'): AMKX 50 EASY

EASYLOC stainless steel coupler to EN 14420 - 7, with lever arrest. Picture shows the version as one-piece coupler with integrated hose tail and Spannfix stainless steel clamp

ZVG 2 EURO

(Push-In-Coupling) to EN 13760. One-handed operation possible.

Production MannTek, Sweden

Solvent filling with integrated vapour recovery in the nozzle

ZVA 25 GR, UTS hose assemblies

Customer protected special design ZVA Slimline 2 & ZVA Slimline 2 GR nozzles

ERV TA:

ERV with white PTFE lining. Used when the chemical resistance of the chosen ERV type is insufficient. Resistant to all commonly used liquids. Electrically isolating, therefore not suitable for flammable liquids in Ex-Zones. Admissible working temperature of expansion joint has to be observed. For maximum pressure of 6 bar – not suitable for vacuum.

Elaflex hose assemblies, nozzles and Rubber Expansion Joints for the chemical industry

Tar (bitumen) spraying hose HB-ST in action

Elaflon Plus FEP hose assemblies, SBC Safety Breakaway Couplings

ZVA Slimline 2 and ZVA Slimline 2 GR, special colour light green

GasGuard LPG nozzles

GG1E, GG1DN, GG20H, GG30

Elapharm EPH 25 OHM-G

ELAPHARM OHM G electrically conductive 'Ω / T', light grey cover. Corresponds to DIN 26055-3 / EN 16820, Type A. FDA conform. Homogeneous elastomer hose construction with smooth, black Teflon® PTFE liner.

MK-A 80 SS, TW female coupler with Active Safeguard Lever, VB 80 SS

AMK 25 EASY

EASYLOC ('Camlock' stainless steel coupler to EN 14420 – 7 for male adapters AVK with captive seal) with lever arrest

Storz Safety Coupling SHK

upon uncoupling, the safety dust plug first falls into holding claws, relasing an eventual pressure within the system. Only then the dust cap can be fully taken off. - increased protection for the operating personnel. Easy to use, no additional pressure release necessary, slim design, does not build up, no freezing up in the dome section.

Terminal / gantry: TW hose assemblies for bottom loading of road tankers

Urea solution filling of a car:

ZVA LV for AdBlue^®, Slimline 16 for AdBlue^® (blue cover)

oasis TH Tank Head Valves, CNG trailer

Boat refuelling, ZVA Slimline 2 GR

Hoses for Liquefied Petroleum Gas / Autogas

LPG 13, LPG 16 black/orange, LPG 19

Oasis EC100 electrically isolating couplers for CNG

GasGuard LPG nozzle GG30

LPGas nozzle with Bayonet connection according to EN 12806 - 2003 for the filling of commercial and passenger Autogas vehicles as well as mobile and small stationary storage tanks with propane and butane. New : 4-slot design to facilitate connection of the nozzle to the vehicle fill point. New nose piece design to reduce the released gas upon valve closure, incorporating improved gas release method to minimise the risk of splash back.

ZVG 2 ACME nozzle for L.P. Gas / Autogas

LPG nozzle for vehicle refuelling with liquefied petroleum gas (propane, butane and mixtures) up to 50 l / min. Working pressure 25 bar. Test pressure 40 bar. Burst pressure > 100 bar. Temperature range - 25° up to + 70° C, 'LT'-Type down to - 40° C.

Oasis Engineering Ltd, New Zealand (CNG refuelling products)

Production Picture 18

ELAFLEX Hamburg

Narrow aisle stock fittings

Slimline quality dispensing hose for the forecourt

Equipment truck for dangerous goods accidents, Elaflon PTFE universal hose assembly, DDC Dry Disconnect Coupling

Hose assemblies

for dangerous goods: ELAFLEX quality